Forum Accessories POE

This topic contains 9 replies, has 6 voices, and was last updated by  deviha 2 years, 11 months ago.

Viewing 10 posts - 1 through 10 (of 10 total)
  • Author
    Posts
  • #5518

    thericksteruk
    Participant

    Hi, i have just purchased the RLC-423 from Amazon in the UK,
    i am a little confused with which POE injector to purchase the one I'm looking at was – TP Link TL-POE150S would this be ok as looking at the manual it says: DC12V PoE (802.3at) Power consumption 22W.

    Any help would be gratefully appreciated.

    Cheers, Rich

    #5519

    thericksteruk
    Participant

    I should add that : DC12V PoE (802.3at) Power consumption 22W is stated on reolink manual.

    #5544

    Anonymous

    Hi thericksteruk, as the manual said the Power consumption is 22W. So the PoE injector's output should more than 22W to support it's warking. The DC 12V and PoE(802.3at) are the two ways of power supply.

    #7253

    yvon001
    Participant

    Hi, I have the same question, and I realize that I need a Power Injector of 802.3 at standard, but can it a passive injector as I was told that some of the cameras need specifics.

    Yvon

    #7384

    Anonymous

    Hi, I have the same question, and I realize that I need a Power Injector of 802.3 at standard, but can it a passive injector as I was told that some of the cameras need specifics.

    Yvon

    The power output of passive injector should satisfied your camera. Please kindly note.

    #7901

    drhudspeth
    Participant

    I bought the 4-camera Reolink RLK8-410B system plus two RLC-423 cameras.  I have tested the system with all 6 cameras and the NVR seems OK to power them, although I have not tried both of the 423 cameras on auto patrol.  Should I be worried about the NVR being able to supply the 22 watts apiece to those cameras and the four RLC-410 cameras?  I don't know how much power the 410 cameras use.  I can connect the 423 camera power supplies to each of those cameras if needed for a stable system, thanks.

    #7903

    drhudspeth
    Participant

    I have the Reolink RLK8-410B4 system including four of the 410 cameras and the 8-port POE injector NVR. I added two RLC-423 PTZ cameras which I understand each take 22 watts. Should I be concerned about overloading the NVR POE? I can wire the power bricks that came with the 423 cameras to them and remove a lot of the power draw, if you think advisable.

    I haven't finished installing the system yet, but I did connect everything up including both 423 cameras and let it run for a few hours, although I didn't have the 423 cameras patrolling and thus continuously using their motors. The NVR and its power supply was warm but not nowhere near hot. However I'd like an expert opinion instead of just a literal ”hands-on” guess :).

    TIA

    #7936

    Anonymous

    Hi, please kindly refer to below:
    power
    And we suggest that when your NVR has connected 4 RLC-410 then you'd better connect one RLC-423. Or you can add a PoE injector for the second RLC-423. Thanks for your understanding.

    #8612

    William
    Participant

    My configuration consists of a POE+ (802.3at) (30w per port) switch to which I attach three RLC-423 which uses a DC12V PoE (802.3at).  Do I need a splitter or can I plug the CAT6 run from the switch directly into the RJ45 jack on the camera without the use of a splitter?

    #13398

    deviha
    Participant

    Hi, i use a SWITCH TEF1105P TENDA to manage 2 RLC-423 and it works fine

Viewing 10 posts - 1 through 10 (of 10 total)

You must be logged in to reply to this topic.